How To Make A Window Flower Box Out Of Wood

By   | Last Updated : September 21, 2021 | Filed In : DIY & How To

Do you have a artistic side? Then this projection is for you. Flower boxes are a great way to bring some colour into your life and building your own can be extremely fun. Let's accept a wait at how to make a wooden window blossom box to hang outside your domicile.

Add together some colour with a homemade flower box. Credit: Shutterstock

Supplies and tools

Before y'all begin your project, make sure y'all have a plan in listen. In that location are many unlike flower box designs out there, some easy and some more than challenging.

For this project, we'll be working with a simple bloom box design that beginners will exist able to take on. The end result will resemble the picture above. Here's what you lot demand to get started:

Tools

• Hammer
• Drill and drill $.25
• Hand or circular saw
• Measuring tape
• Pencil
• Sander and sandpaper
• Paintbrush
• Spirit level
• L-square ruler

Supplies

• Screw plugs
• Screws
• Nails
• Wooden planks
• Wood preservative, stain or sealant
• Plastic lining
• L-brackets
• Wood glue

Method

At present that yous accept all the tools and supplies required to complete this task, let'due south take a wait at how to put together this blossom box.

Step one: Accept some measurements

About windows are designed to be a standard width of 488 mm, 630 mm, 915 mm, i,200 mm or 1,770 mm. The easiest way to figure out how long your flower box needs to exist is to mensurate the width of the window. For an outdoor, wall-hung flower box, you tin brand the long sides of your blossom box just a scrap longer than the width of the window.

Measure out the window past placing one cease of your measuring tape on the corner of the window where the walls see. Extend the measuring tape all the manner to the other corner to discover the width of your window.

Add betwixt ten to 20 cm to your flowerbox measurements to make sure the box covers the window and just a footling more on the side. To get the measurements of your flowerbox, brand certain the edge of the plank you'll be measuring is square. Use the L-square ruler to bank check this by placing one edge of the ruler on the length of the plank and line upwards the other with the edge yous want to measure out. If it lines up perfectly, your plank is cut square, if non, draw a line to correct it afterward.

Measure from your corrected edge to 10 or xx cm longer than your window'southward width. This ways that if your window is 630 mm broad, your flower box sides will demand to exist 830 mm. Make certain to mark the cutting-off and make a directly line with the L-square. This line will serve every bit a guide when the time comes to cut out your flower box sides.

Keep in heed that you lot volition need three long planks and two curt planks for your flower box. To find the measurements of the short sides, mensurate the width and depth of the planks. To get your height, take the width of the side planks minus the depth of these planks. For example, if the width is 15 cm and the depth is 2.5 cm, yous will need to measure 12.five cm for both sides.

Doing this will allow the short sides to sit level with the long side planks while plumbing fixtures on superlative of the bottom plank.

 Step 2: Cut the planks

Now that all your measurements are done, you can start the cutting procedure. For this, you will demand either a handsaw or a circular saw.

Find your pencil marks to know where to make your cuts. Hold down the planks and commencement sawing along the line. One time done you should have iii long planks and two short ones. Don't forget to correct any edges that aren't square.

Stride 3: Construct the flower box

For this step, yous will need your wood gum, screws, a drill and drill $.25. Start by securing one side to the bottom. Simply place the chosen bottom plank flat on your workbench or clench information technology if you take a vice. Place the 2nd plank at a xc-degree bending to the first. Use a drill to create a pigsty through both planks. Identify some wood glue between the planks, printing them together and insert the spiral into the hole yous just created.

This will secure the outset corner of the side and bottom planks. Move over to the other side and practise the same. To secure the rest of the plank you volition need between i to 3 more screws to secure the center of the plank.

Now you can remove it from the vice if yous used one. If not, simply plough the partial box and so you can see the other long side. Secure this plank in identify the same mode yous did the offset. You should now have a bottom with two long sides attached to it.

At present you can turn the one-half-constructed box and then that one of the curt sides face you. Identify some glue and and so insert the short side. Secure it in place with two or three screws on each side and at the bottom. This will ensure it is secure to both long sides and the bottom plank. Practise the same on the other side.

Step 4: Create a smooth finish

For this step, get out your sander and sandpaper. Make sure to sand over all the sharp edges and round off the corners. This will create a smooth finish and a more elegant look. Sanding volition besides remove all the splinters and prepare your wood for painting.

Footstep five: Seal the wood

Now yous will need a forest preservative, stain or sealant. Employ a paintbrush and embrace your whole flower box in sealant/preservative. This volition forbid the wood from rotting in one case you add soil and water to your box.

It is best to allow the showtime coat to dry out thoroughly before applying a second and even third coat. If you haven't created any drainage holes yet, now is the time. Utilise a cup drill bit to create sizable holes for water to drain through. Brand sure to sand the edges and then paint the holes with wood sealant.

Step 6: Line the inside of the box

The final footstep requires the liners, nails, wood mucilage and hammer. The liners will forestall the soil and water from coming in direct contact with your wooden box. This will help to preserve the woods and brand it last much longer.

Just identify glue all over the inside of your box, use the plastic liner and smooth it on top of the glue to secure it in place. Make certain to create holes that line upwards with your drainage holes. Use pocket-size nails to create neat edges where the liner is folded over and hammered in identify. Do the aforementioned all effectually the top to create a neat finish.

Simply fold the liner in on itself and hammer a small nail through to keep it folded and secure. Now all that's left to practice is to secure your flower box to the wall.

Stride vii: Secure the box

At present that your box is done, it is finally fourth dimension to secure it to the wall. For this, you will demand a drill, drill $.25, 50-brackets, screws, screw plugs and a spirit level. Here's what you need to do.

The outset thing you'll exist doing is mark where the L-brackets need to become. For this use a pencil, L-bracket and spirit level. Marker where the first bracket needs to get with a pencil, drill holes where y'all've made marks, insert spiral plugs into the holes and so place the L-subclass dorsum over the holes. One time it'south lined upward, insert the screws and use the drill to screw them into the wall until your bracket is secure.

Earlier securing your 2d bracket, place your box on the start subclass and agree it upward with the 2nd subclass. Identify your spirit level on the edge of the box and lower or lift the bracket y'all holding until the fiddling bubble indicates that your box is level. When level, hold the bracket tightly against the wall and make marks with the pencil in the spots where the screws need to get.

You lot tin can now put downwardly the flower box and the bracket. Drill the holes for the screws, insert the screw plugs and line up the bracket with the holes. Employ the drill with a screw flake to spiral in the screws and secure the subclass to the wall.

If you have a short blossom box, two brackets will do the trick with 1 at each terminate. If your flower box is quite long, you lot volition need to support information technology in the middle by adding i or two more brackets. Just make certain they line upwardly nicely with your blossom box in the same way you lot did the 2nd bracket.

Once you've secured the brackets to the wall, you lot tin fix the brackets to the bloom box by drilling screws into the wood from underneath.

Congratulations! Your flower box is now gear up to exist filled and planted with the flowers of your option.

Read more: What can I constitute in a flower box?

Get creative with your window box planting. Image credit: @pineapplesonparry

FAQs

What wood is all-time for window boxes?

Wood that is naturally rot-resistant such as cedar or redwood is a dandy selection for window boxes. This wood will be in direct contact with moisture and thus needs to be treated properly to avoid your box falling autonomously prematurely. Naturally rot-resistant wood volition terminal even longer when treated properly.

What makes woods waterproof?

Forest sealants such as varnish are a bully choice if y'all need your wood to be waterproof. It volition also protect the wood against rot. Other choices include oils such every bit linseed or tungsten oil. You tin can also paint your wooden flowerbox in a multifariousness of colours. The pigment will help to seal the forest against water harm.

Does a wooden blossom box need a liner?

Yes, wooden planter boxes demand to exist lined. The lining protects them against water damage and prevents rot. This volition prolong the lifespan of your planter and help it wait good for longer.

Recommended Reading

Source: https://www.gardenpatch.co.uk/how-to-make-a-wooden-window-flower-box/

Posted by: whipplemintwoubity.blogspot.com

Share this post